
The GTS is the most extreme F82 BMW M built: stripped, caged, and fitted from the factory with water/methanol injection that lets the S55 run 493 bhp standard. Samuel takes it further still, Stage 1 through to a fully bespoke big-turbo build, hand-calibrated on our 4WD dyno in Manchester.

| Stage | Target | Price |
|---|---|---|
| Stage 1 | 520 bhp · 700 Nm | £450 · £550 dyno |
| Stage 2 | 560 bhp · 750 Nm | £450 · £550 dyno |
| Stage 3, Hybrid Turbo | 600-1200 bhp depending on spec | £1,200 dyno only |
| Stage 3, Big Turbo Kit | 600-1200 bhp depending on spec | POA |
Built for a single year, 2016, in strictly limited numbers, the F82 M4 GTS goes further than any other car on this platform: a stripped-out, roll-caged, weight-reduced M4 with a factory water/methanol injection (WMI) system feeding the S55's intake charge, enough cooling capacity to let BMW run 493 bhp and 600 Nm from the factory, the highest standard output anywhere in this family. Coupe-only, M-DCT only, no manual option and no convertible version was offered. The WMI hardware isn't an aftermarket add-on here, it's fitted from new and stays in place through every stage of tuning, which gives the GTS a genuinely unusual starting point: a factory cooling system already sized for far more ignition timing than the stock turbos alone can use.
The GTS arrives from the factory closer to Stage 1 territory than any other S55 car: 493 bhp / 600 Nm stock against a Stage 1 target of 520 bhp / 700 Nm, just a 27 bhp gain, though torque still climbs by 100 Nm. That's not a sign there's little left to find, it's the opposite: the factory water/methanol injection cooling the intake charge means Samuel can run more aggressive ignition timing on the stock turbos than on any other car in this range, so the software recalibration leans harder on timing and less on raw boost to get there. Stage 2 adds downpipes, a sports midpipe and intakes, and with the WMI already doing its job on intake temperatures, the jump to 560 bhp / 750 Nm comes with less risk of the timing being pulled back under load than it would on a car without factory water injection.
Beyond Stage 2, the GTS reaches the same 1200+ bhp ceiling as the rest of the S55 range, either through a hybrid turbo build or a full big turbo kit with port injection or an HPFP lift kit such as Dorsche. Given how few GTS cars exist, most stay closer to Stage 2 to preserve originality, but the WMI system means the ones that do go further have a genuine head start on cooling. As with every stage on this car, it's calibrated in-house and fully reversible, WMI included.
Stage 1 on the GTS is the smallest Stage 1 jump anywhere in the S55 range on paper, 493 bhp / 600 Nm to 520 bhp / 700 Nm, just 27 bhp, because BMW's factory calibration was already extracting more from this car than from any other standard S55 model. What makes it different from a simple recalibration is the hardware already on the car: the factory water/methanol injection keeps intake temperatures down enough that Samuel can run noticeably more aggressive ignition timing here than on a car without WMI, so the gain in feel is larger than the bhp figure alone suggests. No hardware changes, fully reversible, done on the dyno in one session.
Fitting downpipes, a sports midpipe and intakes and recalibrating around them brings the GTS to 560 bhp / 750 Nm, the same Stage 2 target as every S55 car, but the factory WMI changes how that figure is reached. With intake charge temperatures already under control from the water/methanol system, Samuel has more room to lean on ignition timing rather than pulling it back to manage heat, a genuine advantage over cars running Stage 2 without factory water injection. It's still entirely on the stock turbos, so beyond the WMI system's own servicing and reservoir top-ups, there's nothing extra to look after.
Stage 3 Hybrid Turbo fits reworked stock-frame turbos alongside the Stage 2 hardware, running from 600 bhp up to 1200+ bhp depending on spec. The GTS's factory WMI is the standout advantage at this stage: with intake temperatures already managed by the water/methanol system, the reworked turbos can be run with more confidence in the ignition map than on an S55 car relying on fuel enrichment alone to control heat. Given how few GTS cars were built, this is a route we approach carefully, building around preserving as much of the car's factory character, and its WMI hardware, as possible.
Moving to a full-frame turbo is what the Big Turbo Kit route means in practice, with port injection or an HPFP lift kit such as Dorsche supplying the extra fuel it needs; pricing is POA, and every build is specified individually. On the GTS, the factory WMI system remains genuinely useful even at this level, giving Samuel more scope with ignition timing than on cars without it, though given how limited GTS production was, this is the rarest Stage 3 build we're asked to do in the entire S55 range. Output covers the usual 600 to 1200+ bhp band this stage runs to across the range, mapped from a blank sheet once the hardware's on the car.
The S55 is BMW M's 3.0-litre twin-scroll, twin-turbocharged straight-six, built from 2014 to 2020 and fitted to every M2 Competition, F80 M3 and F82/F83 M4 that left the factory, plus the run-out M3 CS, M4 CS and water-injected M4 GTS. It replaced the naturally aspirated S65 V8 of the previous-generation M3, and it was BMW M's first fully boosted engine for a 3 Series or 4 Series M car: a closed-deck aluminium block, forged crank and rods, and two mono-scroll turbochargers, one per cylinder bank of three, feeding a single MEVD17 DME. Factory outputs across the range span 410 bhp in the M2 Competition up to 493 bhp in the M4 GTS, but every variant is built on the identical block, the identical turbo hardware and the identical engine management. Only the calibration and, on the GTS, a factory water/methanol injection system, separate one car's stock output from another's, which is why the tuning ceiling is the same regardless of which S55 car turns up on Samuel's 4WD dyno.
Stage 1 is a software-only recalibration, no hardware changes, and takes the whole range to 520 bhp / 700 Nm. Stage 2 adds downpipes, a sports midpipe and induction upgrades and moves that to 560 bhp / 750 Nm, freeing up the exhaust and intake restrictions the stock turbos are working against. Beyond that, the S55's factory turbos become the limiting factor rather than the block underneath them, which still has plenty of headroom: Stage 3 splits into a hybrid turbo build, reworked stock-frame turbos with larger internals, or a full big turbo kit with port injection or an HPFP lift kit such as Dorsche, either route capable of 600 to 1200+ bhp depending on the rest of the build. Every stage is calibrated in-house on Samuel's 4WD dyno rather than pulled from a generic map file.
Bootmod3 (BM3): Samuel runs Bootmod3 on the S55 as the primary platform for Stage 1 and Stage 2 work, with on-device map switching between stock, Stage 1, Stage 2, valet and any custom Stage 3 base maps, plus built-in datalogging. It's the platform used for the majority of Stage 1/Stage 2 S55 cars through the Manchester workshop.
MHD: MHD is available as an alternative flashing platform for the S55, and Samuel calibrates bespoke maps for it in exactly the same way as Bootmod3, on the same 4WD dyno session. Some customers prefer its app-based flashing and logging; either platform gets the same hand-built calibration underneath.
MG Flasher: MG Flasher doesn't currently support the S55 and isn't a route offered on this engine. If that changes, this page will be updated; until then, Bootmod3 and MHD are the two flashing platforms available for S55 tuning here.
Scroll through each stage — your Bapro dyno report fills in as we work, from the first health check to the final validated power run.
Calibration and dyno runs are repeated over several passes until the numbers are right.
Full vehicle scan and mechanical health check before any work begins.
Stock power and torque measured on the four-wheel-drive dyno.
Original calibration read from the ECU and safely backed up.
A bespoke map written for your specific vehicle and goals.
Repeated pulls with live data logging to validate and refine the map.
Confirmation run, road test and a before/after dyno printout.
Not sure which stage or method suits your car? Send us a message and we’ll talk it through.