
The E90 saloon, E92 coupe and E93 convertible carried the N55 through the last years of BMW's most analogue 3 Series generation, the one before electric steering took over. Samuel calibrates every one of them on our Manchester 4WD dyno, from a straightforward Stage 1 remap up to hybrid and big-turbo builds for owners chasing serious numbers.

| Stage | Target | Price |
|---|---|---|
| Stage 1 | 380 bhp · 500 Nm | £399 · £499 dyno |
| Stage 2 | 420 bhp · 550 Nm | £399 · £499 dyno |
| Stage 2+ | 440 bhp · 600 Nm | £399 · £499 dyno |
| Stage 3, Hybrid Turbo | Up to 800 bhp depending on spec | £1,000 dyno only |
| Stage 3, Big Turbo Kit | Up to 800 bhp depending on spec | POA |
BMW fitted the N55 to the E90 saloon, E92 coupe and E93 convertible from 2010 to 2013, replacing the earlier twin-turbo N54 as production moved on. All three share the same 302 bhp and 400 Nm output, sent through either the ZF 6HP automatic or a 6-speed manual gearbox. This was the final run of 3 Series before the F30 generation switched to electric power steering and a noticeably different character behind the wheel, which is exactly why the E9x cars still command such a following among people who want feel over refinement. It's one of the most popular N55 platforms Samuel works on, precisely because the chassis rewards the extra power so directly.
The E90/E92/E93 335i leaves the factory at 302 bhp and 400 Nm, figures that were competitive when the car launched but leave a lot of the N55's actual capability sat unused. Stage 1, a remap with no hardware involved, brings that up to 380 bhp and 500 Nm using headroom already built into the standard turbo and fuelling system. From there, Stage 2 introduces a downpipe, uprated intake or panel filter, and a larger intercooler, and the recalibrated map takes the car to 420 bhp and 550 Nm with better-controlled intake temperatures under sustained load. Stage 2+ keeps that same hardware and adds a uprated fuel pump, reaching 440 bhp and 600 Nm, which is as far as the factory turbo itself can reasonably be pushed. Past Stage 2+, the ceiling comes down to turbo choice: a hybrid build reuses the standard housing with larger internals, while a full big-turbo kit with port injection and an uprated low-pressure fuel pump opens up four-figure potential for cars built specifically for that. Every one of these stages is built and logged on our in-house 4WD dyno in Manchester, and every file can be reverted back to the factory calibration whenever it's needed.
No hardware, just a full recalibration of boost, timing and fuelling within the standard turbo's safe limits, taking the 335i from 302 bhp and 400 Nm to 380 bhp and 500 Nm. On the E9x chassis, with its hydraulic steering and relatively light kerb weight compared with the F30 that followed it, that extra torque is immediately obvious through the wheel and in how eagerly the car changes direction mid-corner. £499, built on the dyno at our Manchester workshop, and fully reversible if you ever need the car back to stock.
Fit a downpipe, an uprated intake or panel filter, and a bigger intercooler, and Samuel rebuilds the calibration around that hardware to bring the E9x 335i to 420 bhp and 550 Nm. The extra cooling capacity matters more on this generation than people expect, sustained runs on track or a long motorway pull no longer see the same heat soak that catches out a Stage 1-only car. £399 (£499 dyno tuned) for the map on top of the hardware, and still built specifically around your car's setup rather than a generic file.
The same downpipe, intake or panel filter, and intercooler carry over from Stage 2, with a uprated fuel pump added to support the extra fuelling Stage 2+ needs. That combination takes the 335i to 440 bhp and 600 Nm for £399 (£499 dyno tuned), and represents the practical limit of what the factory turbo can support before the conversation shifts to hybrid or big-turbo hardware. For most E9x owners using the car on the road, this is where the build stops.
A hybrid turbo build reuses the factory housing but replaces the compressor and turbine internals with larger, more efficient components, built on top of the downpipe, intake, intercooler and uprated fuel pump already fitted for Stage 2+. On the E90/E92/E93, that combination takes output up to 800 bhp depending on the exact specification and how the rest of the car has been prepared to handle it, gearbox, cooling, fuelling. £1,000 for the build, hand-calibrated for your specific car on our Manchester dyno rather than loaded from a generic map.
Beyond the hybrid route sits the full big-turbo kit: a complete turbo replacement, port injection to handle the fuelling, and a larger low-pressure fuel pump, alongside the same downpipe, intake, intercooler and uprated fuel pump used further down the range of stages. This is the ceiling for the E9x 335i on the N55, up to 800 bhp depending on spec, priced POA because every build like this is specified around what the car and the customer actually need, road, track, or both.
BMW introduced the N55 in 2009 as a simplified, single-turbo replacement for the twin-turbo N54, trading a little outright headroom for smoother running, faster spool and a cheaper unit to build and own. A single twin-scroll turbocharger, direct injection and Valvetronic variable valve lift took over from the N54's twin-turbo layout, and the result pulls cleanly from low revs while still holding a substantial amount of headroom in its factory internals. Across a production run that ran from 2010 to 2018, the N55 found its way into everything from the 1 Series hot hatch to the X3 SUV, wearing outputs anywhere from 302 bhp in the earliest cars up to 365 bhp in the F87 M2, but underneath the badge it's fundamentally one block, one turbo architecture, and one set of tuning limits.
That shared hardware is why Stage 1 through Stage 2+ figures are near-identical whichever N55 car rolls onto Samuel's dyno: the block, injectors and turbo housing are the same regardless of which BMW they're bolted into, so the software calibration does almost all of the early-stage work. Stage 1 is a pure remap, no hardware, built and logged on our in-house 4WD dyno in Manchester. Stage 2 and Stage 2+ add supporting hardware, a downpipe, uprated intake, and a bigger intercooler, to keep the factory turbo fed and cool as boost and timing increase. Beyond that, the ceiling depends on how far you want to take the turbo itself: a hybrid upgrade keeps the factory frame and housing but swaps the internals for larger, more efficient parts, while a full big-turbo kit replaces the entire turbo and adds port injection and a larger low-pressure fuel pump to support four-figure boost potential in the right spec. Every N55 tune is built specifically for the car it's fitted to, not pulled from a generic file library.
Bootmod3 (BM3): Samuel calibrates the N55 on Bootmod3 where the car's platform supports it, giving live map switching between Stage 1, Stage 2 and Stage 2+ files plus datalogging through the same connection used for the flash. It's the platform we default to on most N55 cars that support it, built around per-car calibration rather than a shared base map. The exception is the Z4 35i E89, which we tune with our own tools rather than Bootmod3 or MHD.
MHD: MHD is the other route we calibrate N55 cars on, particularly where Bootmod3 coverage doesn't extend to a specific chassis or model year. Flashing and logging both run through the MHD app, and the tune underneath is the same hand-built calibration regardless of which platform delivers it. On the E82/E88 135i and E90/E92/E93 335i, MHD is the only platform we offer.
MG Flasher: MG Flasher's coverage is built around BMW's newer B-series and S-series engines, and the N55, in production from 2010 to 2018 and largely superseded before MG Flasher's platform matured, isn't currently a route we offer tuning through. If that changes we'll update this page, but we won't claim support on this engine that we can't actually back up on the dyno.
xHP: Where the ZF automatic gearbox is fitted, xHP handles the transmission side, sharper shift response, adjusted shift points, and launch control where the hardware allows. It's a separate flash to the ECU tune and priced accordingly, offered on the N55 cars in this range that run the ZF 6HP or ZF 8HP automatic.
Scroll through each stage — your Bapro dyno report fills in as we work, from the first health check to the final validated power run.
Calibration and dyno runs are repeated over several passes until the numbers are right.
Full vehicle scan and mechanical health check before any work begins.
Stock power and torque measured on the four-wheel-drive dyno.
Original calibration read from the ECU and safely backed up.
A bespoke map written for your specific vehicle and goals.
Repeated pulls with live data logging to validate and refine the map.
Confirmation run, road test and a before/after dyno printout.
Not sure which stage or method suits your car? Send us a message and we’ll talk it through.