
BMW's smallest 2 Series coupe carries the same N20 turbo four that powers half this range, sitting one rung below the six-cylinder M235i in the showroom but sharing its F22 shell and chassis. Tuned properly, the four-cylinder 228i closes a lot of that gap for a fraction of the outlay, and Samuel's calibration work takes it well past what BMW allowed from new.

| Stage | Target | Price |
|---|---|---|
| Stage 1 | 280 bhp · 400 Nm | £399 · £499 dyno |
| Stage 2 | 320 bhp · 450 Nm | £399 · £499 dyno |
| Stage 3, Hybrid Turbo | 400 bhp · 500 Nm (depending on spec) | £850 dyno only |
The F22 228i ran from 2014 to 2016 as the entry point into BMW's second-generation 2 Series, available only as a coupe, there was never a convertible version wearing the 228i badge. Under the bonnet is the same 2.0-litre N20 turbo four found across this whole family, producing 245 bhp and 350 Nm as standard and sending it rearward through a ZF 8HP automatic. Positioned below the N55-powered M235i in BMW's own hierarchy, the 228i shares its chassis architecture and much of its underpinnings with that faster sibling, which is exactly why it responds so well to tuning: the platform was engineered for more power than the four-cylinder engine was ever allowed to produce.
BMW held the 228i back to keep clear water between it and the M235i, and that gap is largely artificial rather than a hardware limitation. Stage 1 is a software-only recalibration that lifts the standard 245 bhp and 350 Nm to 280 bhp and 400 Nm, using the factory downpipe, intake and intercooler, and for a lot of 228i owners it's enough on its own to make the coupe feel like it's punching at the weight class above where BMW positioned it.
Stage 2 needs supporting hardware, an upgraded downpipe, intake and intercooler, before the ECU can safely be recalibrated to 320 bhp and 450 Nm; the standard parts simply run out of headroom at that boost level. Stage 3, the hybrid turbo build, swaps the factory turbocharger for a larger hybrid unit and takes the ceiling out to around 400 bhp and 500 Nm, a figure that puts the four-cylinder coupe within reach of some proper performance machinery, all while keeping the same lightweight F22 shell.
Every stage is calibrated on 117Speed's in-house 4WD dyno in Manchester, with Samuel tuning the file to your specific car rather than loading a stock map. Stage 1 and Stage 2 remain fully reversible; the hybrid turbo is the one stage that involves permanent hardware.
The 228i's Stage 1 tune moves it from a standard 245 bhp and 350 Nm to 280 bhp and 400 Nm purely through software, no parts required. Given how much the 228i and M235i share underneath, this stage alone starts to erode the performance gap BMW built into the range through calibration rather than engineering, and it does so without touching the factory downpipe, intake or intercooler. It's the stage most 228i owners book first, both for the cost and because it changes the car's character noticeably without any commitment to hardware. Everything is done on the dyno in Manchester, tuned specifically to your car's condition and mileage.
Stage 2 asks the 228i's supporting hardware to catch up with what the ECU can now demand: a larger intercooler, upgraded intake and a freer downpipe, all needed before Samuel can safely push the calibration to 320 bhp and 450 Nm. This is the stage where the 228i starts to feel properly quick rather than merely brisk, closing meaningful ground on the M235i it sits beneath in BMW's own lineup. The hardware needs fitting before the car comes in, since the Stage 2 map is built around how that specific combination of parts flows, not a generic upgrade file.
At Stage 3, the factory turbocharger comes off the 228i entirely, replaced with a hybrid unit built to flow considerably more air than BMW's original part. Paired with the Stage 2 hardware already in place, this takes the coupe to roughly 400 bhp and 500 Nm, more than 60% over standard and enough to make the lightweight F22 shell feel like an entirely different proposition. This is the highest-effort stage in terms of parts and labour, and it's tuned as a bespoke project on the dyno rather than a standard file. It's aimed at 228i owners who want the four-cylinder car to properly embarrass its badge.
BMW's N20 replaced the naturally aspirated N52 and N53 sixes with something smaller, turbocharged and, on paper, less charismatic. In practice it became one of the most widely deployed engines in BMW's history: a 2.0-litre turbocharged inline-four with direct injection, Valvetronic and a single twin-scroll turbo, built from 2011 to 2016 across the 1, 2, 3, 4 and 5 Series plus the X1, X3 and Z4. The same block and largely the same ECU logic underpin every car in this family, which is why the tuning numbers below repeat so consistently from one model to the next.
Stock output sits at either 218 bhp (125i) or 245 bhp (everything else in this family), both well short of what the hardware can actually support. The factory tune is conservative by design: BMW built the N20 to satisfy emissions targets, warranty claims and a wide range of markets, not to extract everything the turbo and internals can handle. That gap between what the ECU allows and what the engine can take is where Samuel's calibration work happens, using 117Speed's in-house 4WD dyno in Manchester to validate every stage on the car in front of him rather than a generic map pulled off a shelf.
The N20 has a couple of known weak points worth knowing about before you tune one: timing chain guide wear on higher-mileage examples, and some engines are prone to oil consumption. Neither is caused by tuning, but a car with an already-worn chain guide isn't one to push hard at Stage 2 or Stage 3 without a look underneath first. Samuel checks the basics before any car goes on the dyno and flags anything that needs attention before a tune is signed off.
117Speed's own tools: We tune every N20 car with our own tools rather than Bootmod3 or MHD, so there's no platform licence to buy. Map switching, ethanol and flame map slots aren't offered on this engine.
MG Flasher: Not currently offered on the N20. MG Flasher's coverage focuses on BMW's newer B-series and S-series engines, and the N20 (2011-2016) sits outside that window. If that changes in future this page will be updated, but right now it isn't a route we offer on this engine.
xHP: Worth adding alongside a Stage 1 or Stage 2 tune on any N20 car running the ZF 8HP automatic, sharpening shift points and response to match the extra power. Where a car in this family runs a manual or DCT gearbox instead of the ZF 8HP, xHP doesn't apply and isn't offered.
Scroll through each stage — your Bapro dyno report fills in as we work, from the first health check to the final validated power run.
Calibration and dyno runs are repeated over several passes until the numbers are right.
Full vehicle scan and mechanical health check before any work begins.
Stock power and torque measured on the four-wheel-drive dyno.
Original calibration read from the ECU and safely backed up.
A bespoke map written for your specific vehicle and goals.
Repeated pulls with live data logging to validate and refine the map.
Confirmation run, road test and a before/after dyno printout.
Not sure which stage or method suits your car? Send us a message and we’ll talk it through.