
The 125i is the warm end of BMW's 1 Series, N20 turbo four under the bonnet of the F20 five-door and F21 three-door. It's also the most conservatively tuned car in this entire N20 family from the factory, which means Stage 1 alone closes more of the gap to the car's true potential than on any other model here.

| Stage | Target | Price |
|---|---|---|
| Stage 1 | 280 bhp · 400 Nm | £399 · £499 dyno |
| Stage 2 | 320 bhp · 450 Nm | £399 · £499 dyno |
| Stage 3, Hybrid Turbo | 400 bhp · 500 Nm (depending on spec) | £850 dyno only |
Built between 2012 and 2016, the F20 and F21 125i sit at the entry point of BMW's N20-powered 1 Series range, the five-door hatch and three-door coupe-hatch sharing the same 2.0-litre turbocharged inline-four and the same ZF 8HP automatic sending drive to the rear wheels. At 218 bhp and 310 Nm, the 125i runs the lowest factory output of any car in this N20 lineup, a full 27 bhp below the 245 bhp figure everything else in the family ships with. That's not a limitation of the hardware, it's simply how BMW positioned the car in the range. Underneath, it's the same engine as the 328i or the X3 28i, just held back further by software.
Because the 125i starts lower than the rest of this family, the numbers move further at every stage. Stage 1 is a pure software recalibration, no hardware changes, and it takes the car from 218 bhp / 310 Nm up to 280 bhp / 400 Nm, a 62 bhp increase that's proportionally the biggest jump on offer anywhere in the N20 range. It's built around the standard downpipe, intake and intercooler, so it's the option most owners start with, and for a lot of 125i drivers it's also where they stop: the difference in real-world response is immediate and the car stays entirely usable day to day.
Stage 2 asks for hardware to go with the software: a freer-flowing downpipe, upgraded intake and a larger intercooler, unlocking 320 bhp and 450 Nm once those parts are fitted and the car's back on the dyno for a final calibration pass. Stage 3, the hybrid turbo build, replaces the factory turbocharger itself and pushes the 125i to around 400 bhp and 500 Nm depending on the exact hybrid turbo specification chosen, which is close to double what the car left the factory with.
Every stage is delivered as a flash to the car's own ECU, done on 117Speed's in-house 4WD dyno in Manchester, and every stage below the hybrid turbo build can be reverted back to standard whenever you need to.
Stage 1 on the 125i is where the factory's conservative tuning shows up clearest: 218 bhp and 310 Nm becomes 280 bhp and 400 Nm from a software recalibration alone, no hardware fitted, no compromises to daily usability. That's a 28% power increase and a 29% torque increase, figures that outstrip every other Stage 1 gain in this N20 family simply because the 125i had further to climb. Samuel calibrates each car individually on the dyno rather than loading a generic file, checking fuelling, boost and timing against what that specific engine can safely take. For most 125i owners this single stage transforms how the car drives without ever touching a spanner.
Stage 2 builds on that Stage 1 base once the supporting hardware is in place: downpipe, intake and intercooler, all upgraded to cope with the extra airflow the higher boost target demands. With those parts fitted, the 125i moves to 320 bhp and 450 Nm, more than 100 bhp over stock and a different car to drive than the one that left the factory. The hardware isn't optional at this stage, the standard intercooler and downpipe simply can't support the numbers safely, so budget for the parts alongside the £399 (£499 dyno tuned) recalibration. Once fitted, the car returns to the dyno for a Stage 2 specific map rather than a generic upgrade.
The hybrid turbo build is the ceiling for the 125i on the N20 platform: the factory turbocharger is replaced with a hybrid unit sized to flow considerably more air, and combined with the Stage 2 supporting hardware it takes the car to around 400 bhp and 500 Nm, the exact figure depending on the specific hybrid turbo fitted. That's very close to double the 218 bhp the 125i left the factory with. This is a bigger undertaking than Stage 1 or Stage 2, both in parts and in labour, and it's calibrated as its own project on the dyno rather than a simple map upload. It's the option for owners who want everything the N20 block can give.
BMW's N20 replaced the naturally aspirated N52 and N53 sixes with something smaller, turbocharged and, on paper, less charismatic. In practice it became one of the most widely deployed engines in BMW's history: a 2.0-litre turbocharged inline-four with direct injection, Valvetronic and a single twin-scroll turbo, built from 2011 to 2016 across the 1, 2, 3, 4 and 5 Series plus the X1, X3 and Z4. The same block and largely the same ECU logic underpin every car in this family, which is why the tuning numbers below repeat so consistently from one model to the next.
Stock output sits at either 218 bhp (125i) or 245 bhp (everything else in this family), both well short of what the hardware can actually support. The factory tune is conservative by design: BMW built the N20 to satisfy emissions targets, warranty claims and a wide range of markets, not to extract everything the turbo and internals can handle. That gap between what the ECU allows and what the engine can take is where Samuel's calibration work happens, using 117Speed's in-house 4WD dyno in Manchester to validate every stage on the car in front of him rather than a generic map pulled off a shelf.
The N20 has a couple of known weak points worth knowing about before you tune one: timing chain guide wear on higher-mileage examples, and some engines are prone to oil consumption. Neither is caused by tuning, but a car with an already-worn chain guide isn't one to push hard at Stage 2 or Stage 3 without a look underneath first. Samuel checks the basics before any car goes on the dyno and flags anything that needs attention before a tune is signed off.
117Speed's own tools: We tune every N20 car with our own tools rather than Bootmod3 or MHD, so there's no platform licence to buy. Map switching, ethanol and flame map slots aren't offered on this engine.
MG Flasher: Not currently offered on the N20. MG Flasher's coverage focuses on BMW's newer B-series and S-series engines, and the N20 (2011-2016) sits outside that window. If that changes in future this page will be updated, but right now it isn't a route we offer on this engine.
xHP: Worth adding alongside a Stage 1 or Stage 2 tune on any N20 car running the ZF 8HP automatic, sharpening shift points and response to match the extra power. Where a car in this family runs a manual or DCT gearbox instead of the ZF 8HP, xHP doesn't apply and isn't offered.
Scroll through each stage — your Bapro dyno report fills in as we work, from the first health check to the final validated power run.
Calibration and dyno runs are repeated over several passes until the numbers are right.
Full vehicle scan and mechanical health check before any work begins.
Stock power and torque measured on the four-wheel-drive dyno.
Original calibration read from the ECU and safely backed up.
A bespoke map written for your specific vehicle and goals.
Repeated pulls with live data logging to validate and refine the map.
Confirmation run, road test and a before/after dyno printout.
Not sure which stage or method suits your car? Send us a message and we’ll talk it through.